VPN Installation Instructions

Virtual Private Network (VPN) can be used by faculty and staff to connect to Weber State's secure network from off campus.  To connect, you will need to have a VPN desktop client installed on the computer you plan to use while off campus.

Weber State supports the Cisco AnyConnect VPN Client which is pre-installed on many 91¶ÌÊÓƵ laptops and can also be installed on personal devices.

Please note: Duo must be enabled on your eWeber account before you can use the VPN. If you are not enrolled in Duo yet, visit the Duo Mobile Self Service channel in the eWeber portal.

Refer to the following sections on this page:

If you require assistance or have any questions, please contact the IT Service Desk.

Cisco AnyConnect VPN Client

The Cisco AnyConnect Secure Mobility Client is the Weber State supported VPN software and what is covered in this instruction set.  However, other VPN clients may work by pointing to our VPN server: vpn.weber.edu

AnyConnect will work on most computing devices.  Click  to see a full list of hardware and software requirements. 

While using 91¶ÌÊÓƵ's network services, users are subject to 91¶ÌÊÓƵ's Acceptable Use Policy for Computing and Network Resources (PPM 10-2).  Violation of this policy may result in a user's network access being suspended.  Note that any sort of peer-to-peer (P2P) connection is strictly prohibited while on campus (Torrents, Limewire, etc.).

Windows Installation Instructions

For campus owned computers, these steps may need administrator privileges which could require you to contact your CTC or the IT Service Desk.


If you are installing VPN software on a Weber State Windows computer, Cisco AnyConnect can be installed through the Software Center application without the need for administrator privileges.  Otherwise a manual install can be performed.

To manualy install Cisco AnyConnect on Windows:

  1. Visit
     
  2. Login with your Wildcat username and password. 
     
  3. Follow on screen instructions to complete the install (this may require administrator credentials, contact your department's CTC or the IT Service Desk for assistance).
     
  4. After the application is successfully installed, click the Start button, then search for the Cisco AnyConnect Mobility Client application.

     
  5. Once the application is open, type vpn.weber.edu in the connection bar then click Connect.

     
  6. A new Central Authentication System (CAS) window will appear asking for your 91¶ÌÊÓƵ username and password. Enter in the required information and click Login.
     
  7. Your computer should now be connected to 91¶ÌÊÓƵ's network services.
     
  8. When finished, disconnect by opening the Cisco AnyConnect Mobility Client and click the Disconnect button.
You will need to re-connect AnyConnect each time you wish to establish a new VPN session.

Mac Installation Instructions

For campus owned computers, these steps may need administrator privileges which could require you to contact your CTC or the IT Service Desk.


If you are installing VPN software on a Weber State Windows computer, Cisco AnyConnect can be installed through the Self Service application without the need for administrator privileges.  Otherwise a manual install can be performed.

To manualy install Cisco AnyConnect on macOS:

  1. Visit
     
  2. Login with your Wildcat username and password. 
     
  3. Follow on screen instructions to complete the install (this may require administrator credentials, contact your department's CTC or the IT Service Desk for assistance).
     
  4. Once it's successfully installed, navigate to the Go menu and click on Applications and find the folder named Cisco.

      

  5. Open the Cisco AnyConnect Mobility Client inside the Cisco folder.

  6. In the connection bar, type: vpn.weber.edu then click connect.
  1.  A new window will appear asking for your 91¶ÌÊÓƵ username and password. Enter the required information and click Login. 
     
  2. Your computer should now be conncted to 91¶ÌÊÓƵ's network services. 
     
  3. When finished, disconnect by opening the Cisco AnyConnect Mobility Client and click the Disconnect button.
You will need to re-connect AnyConnect each time you wish to establish a new VPN session.

Mobile Device Installation Instructions

iOS (iPhone / iPad) 

VPN is not supported on all versions of iOS. A device must have Apple iOS 10.3 or later installed for Cisco AnyConnect to work. 

  1. Download the Cisco Secure Client application from the . 
  2. Open the AnyConnect application once installed. 
  3. Tap Connections and then Add VPN connection.
  4. Next to Server Address enter vpn.weber.edu then select Save in the upper right.
  5. Press Allow on the prompt to allow Anyconnect to add VPN configurations to iOS.
  6. Press Back to go back to AnyConnect's main window, then toggle the AnyConnect VPN option on.
  7. Log in with your 91¶ÌÊÓƵ username and password on the CAS page. 
  8. Your device should now be connected to 91¶ÌÊÓƵ's network.
  9. When finished, disconnect by opening the AnyConnect app and toggle the AnyConnect VPN option to off.
You will need to re-connect AnyConnect each time you wish to establish a new VPN session.


Android

VPN is not supported on all Android devices. You must have Android 4.0 or later installed for Cisco AnyConnect to work. 

  1. Download the Cisco AnyConnect application from the . 
  2. Open the AnyConnect application once installed. 
  3. Tap Connections and then Add VPN connection.
  4. Next to Server Address enter vpn.weber.edu then select Save in the upper right.
  5. Press Allow on the prompt to allow Anyconnect to add VPN configurations to iOS.
  6. Press Back to go back to AnyConnect's main window, then toggle the AnyConnect VPN option on.
  7. Log in with your 91¶ÌÊÓƵ username and password on the CAS page. 
  8. Your device should now be connected to 91¶ÌÊÓƵ's network.
  9. When finished, disconnect by opening the AnyConnect app and toggle the AnyConnect VPN option to off.
You will need to re-connect AnyConnect each time you wish to establish a new VPN session.